BioSemi.nl

BioSemi equipment is compatible with TMS indeed.
You can find many research results of successful BioSemi and TMS equipment on Google Scholar:
https://scholar.google.com/scholar?hl=e ... iosemi+tms

If you want to check the gain specifications of the ActiveTwo system, then you can do this with the two-bucket test: You will need the following: - signal generator - 2 passive AgAgCl electrodes that can be connected to the output of the signal generator. - 2 plastic buckets or 2 glass bowls (never ...

The USB2 Receiver is always problematic when it comes to the "first time" connection upon unplugging. This is tough because we have to move the computer from one part of the office to another in order to test. I think you do not mean the USB Receiver, but you mean the BioSemi USB Trigger Interface....

If the BioSemi USB Receiver is not listed in the Device manager, then it might be that it is detected as an unknown device. If you unplug the USB Receiver and plug it in again, then you can see in the Device manager what device is added. I assume that your Receiver was working correctly on this W10 ...

Coen means that you should press the AgAgCl tips of the CMS, the DRL and 1 of the GSR electrodes together. In practice, this will be difficult, because you may absolutely not use any metals when doing this. When metals will touch the AgAgCl tips, the tip will be contaminated with metal particles and...

Please check the below 6 points: https://www.biosemi.com/faq/AD-box%20shuts-down%20or%20Acquisition%20stops.htm How is the USB Receiver shown in the Device manager? With or without an exclamation mark? If you have access to another W10 PC, than try the USB receiver on that PC (no drivers are needed,...

Dear Rahul, You say that you have problems installing the driver for the USB Trigger Interface (stimulation PC), but the link you shared is for the drivers for the USB Receiver (recording PC) The USB Trigger Interface should install the drivers automatically when the PC is connected to the internet....

Dear Jasna,

Electrode sets with Red Rubber strain relief can be cleaned and handled exactly the same way as the older electrode sets without the Red Rubber.

No, that is not possible.
Only 1 CMSDRL cable can be inserted at the time.
If you plug -in a P32 set with CMSDRL into the A SCSI connector, than you can not also plug-in a CMSDRL cord into the front CMSDRL input.

Why would you like to use the front CMSDRL cord?

Dear Juliette, First you need to know how many channels are installed in SCSI connector C1-32. You can find out how many hardware channels are installed inside your AD-box by running ActiView. Select the 'Offset' page in ActiView with no electrode sets inserted in the AD-box. When a channel is insta...

The information on the website describing the filter has been updated:
"A fifth order cascaded integrator-comb (CIC) filter"

CMSDRL FLAT is the ordercode. There is no image of the CMSDRL FLAT on the website. For EEG we advise Signa gel. For all ECG/EMG/EOG measurements we advise Elefix. The skin on the chest, arms and legs is more difficult to penetrate and make contact with. That is why for ECG/EMG/EOG, a stronger gel is...

Dear Juiliette,

Has your USB Receiver got firmware version 4.0?
If not, then please update your USB Receiver to firmware version 4.0 as described here:
https://www.biosemi.com/faq/install_USB.htm

Best regards,
Robert

Dear Juliette, If the acquisition stops, then first always check if the green power LED on the AD-box is on of off. Assuming that the batteries are working (green LED on the battery is on) If the acquisition stops and the green power LED on the AD-box is off, then there is a situation is described h...

You can actually just re-use the electrodes without washing. Washing an electrode set while there is still gel on the electrodes, can result in a 'wattery' layer which worsens contact with the skin or with a second layer of gel. In other words: the water makes the surface of the gel very slippery. I...

Hi Jennifer, The picture on the Cortechsolutions website shows a child of about 3? years old with a Small headcap: http://www.cortechsolutions.com/Products/Physiological-data-acquisition/Systems/ActiveTwo/Components/Head-caps.aspx The picture shows a 64 channel headcap. The distance between FPz and ...

Infant head circumferences vary quite a lot, even when the infants are of the same age. What is the median head circumference of your 6 month olds? I know of a lab that tried the Infa3 caps on 6 months olds, but they said those were to small. So it looks like Infa2 (38-42 cm) should be the right siz...

Cedrus sells a USB to Parallel converter that is instantly compatible between the Presentation software of Mindware Technologies and the trigger inputs of the BioSemi USB receiver.

http://www.cedrus.com/stimtracker/

Giorgio, I just tried a Large headcap on a subject with 40 cm preauricular distance. I must admit that I also found that T7 and T8 are located a bit too high with respect to the preauricular points. When I tried a Large/XL headcap on this subject, the location was about right. I would recommend you ...

Giorgio, you are using a headcap which is too small. If I understand correctly, since your subject has 40 cm distance between the 2 preauricular points, the 2 cap holders (T7 and T8) right above the 2 preauricular points should be at 4 cm distance of these 2 preauricular points, but you measured the...

Depending on the user and (mainly) the cleaning procedures, my guess would be at least 500 measurements.

Caps can be cleaned with warm or hot water. If necessary, you can use some shampoo. The caps are not really sensitive for cleaning materials. Just let them soak in warm water, this will make the cleaning process easier/faster. Electrodes can be rinsed with tap water without any risk. As long as the ...

The latest set of drivers (beta version) by forum member PMac is now available here:
http://www.biosemi.com/download.htm

Robert, BioSemi

The newest updated Linux driver developed by PCMac is available here:

http://www.biosemi.com/download/USB%20d ... x1.tar.bz2

A new generation of drivers is now available for evaluation. The below link has both the new Windows 64 bit and Linux drivers. http://www.biosemi.com/download/USB%20drivers%20beta/ For the Linux drivers note the following: 1. The 64 bit version was developed and tested on 64 CentOS 5 (Linux 2.6.18 )...

Hi Martina,

Here you can download the USB2 driver
http://www.biosemi.com/download.htm
This driver is suitable for XP&Vista.

Installing the driver is done by right clicking on the file 'BioSemi.inf'
Then select 'Install'

Please see this picture, that explains it all.

http://www.biosemi.com/pics/transfer.jpg

Best regards, Robert(Biosemi)